Carbon Math

Posted By on February 7, 2007 at 9:07 pm

In a multiply-updated post, Glenn Reynolds talks global warming and the effect thereupon of congressional “private” air travel.
In the course of the post, Reynolds cites this statistic from Tourjet (which, as the name implies, is an aircraft chartering agency catering to celebrities):

The typical American is responsible for 10 tons of CO2 emissions annually through their direct energy use of home, cars and air travel, and about 24 tons of CO2 including their purchases, activities and the other services we all share throughout the economy.
By comparison, a Gulf Stream III business jet (10-12 passenger) from New York to Los Angeles will emit around 31 tons of CO2 during the 6 hour flight.

I’m no airplane expert (merely a well-informed hobbyist, you could say) but it seems to me that if a cross-country fight produces 31 tones of CO2, this means the aircraft would have to carry well over 31 tons of fuel, as not all the consumed fuel would be exhausted as CO2. I have a hard time believing that.
Turning to airliners.net we can see a bit of info on the weight of the Gulfstream III:

Empty 14,515kg (32,000lb), operating empty 17,235kg (38,000lb), max takeoff 31,615kg (69,700lb)

Quick math…. OK, so at the very most, the plane can carry 37,700 pounds (18.85 tons) of non-airplane weight.* That’s passengers, luggage, cargo, and fuel. While that is a lot, it’s not 31 tons, it’s not all fuel weight, and not all of of the fuel would be used on a NY-LA flight, since the aircraft’s range is something over 4,000 miles.
Unless, of course, there’s more than one airplane called the Gulfstream III….**
It is hypocritical for “jet set” celebrities and politicians to blather about reducing greenhouse gas emissions while burning fuel by the ton, but accuracy counts, too. In this case, it’s not quite as bad as it appears at first glance.
(So, I hope I got the numbers right….)



* It’s just a guess on my part, but I think the difference between the “empty” weight and the “operating empty” weight might be the airplane plus a full fuel load, which would make the fuel capacity 6,000 pounds.
** Update: Errr… nevermind. I forgot all about the oxygen input into the chemical reaction, which would indeed boost the output CO2 mass to something rather higher than the carbon input into the equation. Good thing I don’t make my living as a chemist.

Just When You Thought The Planking Was Finished

Posted By on February 6, 2007 at 7:52 pm

I’ve been model-making rather than writing. I’m horrible. So anyway….
The hull planking having been completed, I next turned my attention to the deck planking.
The supplied material — .5mm x 4mm strips of something neither basswood nor walnut… maybe tanganyika wood — was a bit disappointing; the color tone was inconsistent, and the edges were somewhat rough due to the coarseness of the grain. I ganged the strips together and mass-sanded the edges, which got them close enough to what I wanted, but because (as usual) there was barely enough supplied to do the job, I had to be careful not to sand too much away.
I then cut all but one of the strips into 75mm segments (the length being decided upon arbitrarily) and, using a #2 pencil, blackened one edge of each strip to simulate the caulking that was historically hammered into the gaps between planks in order to waterproof the deck.
Using wood glue rather than cyanoacrylate, I ran the one uncut strip down the centerline of the deck to use as a starting point for the rest of the planking, and then filled in the rest of the deck, offsetting each row of planks by 25mm to create a “three-butt shift” — ensuring that no two adjacent planks ended at the same spot. I also made sure to trim out the holes for the masts before I completely covered them over.


I was correct about the amount of wood supplied for the deck planking; there wasn’t a single extra strip left over.
When the deck planking was complete, I sanded and scraped it smooth, and applied three coats of varnish, lightly sanding after the first and second coats.
I then rough-cut the gunports, bent and installed the waterways (sorry, too small to photograph) and then installed the inner bulwark planking and finish-cut the gunports.
Next: finishing the hull.